One Big Projector

Keep your iPhone screen awake while projecting

A projection that goes dark halfway through is almost always the phone locking itself, not the projector. The phone is the source of the picture, so when its screen sleeps, the wall goes with it.

There are three settings involved and they can fight each other. This page goes through them in the order that matters, with Apple's own wording where Apple publishes it, and then the part nobody warns you about: a phone driving a projector for two hours gets warm.

Set Settings > Display & Brightness > Auto-Lock > Never. If Never does not hold, check Low Power Mode, which Apple says "Sets Auto-Lock to 30 seconds". To stop a stray tap leaving the app as well, use Guided Access. Apple notes that "Delaying or preventing Auto-Lock may increase power consumption", so put the setting back afterwards.

Turn Auto-Lock off

This is the setting people mean by keeping the screen awake. Apple's steps are three taps, and Never is the last option in the list of times.

  • Go to the Settings app.
  • Tap Display & Brightness, then tap Auto-Lock.
  • Choose Never.

Why it still goes dark after 30 seconds

If the screen keeps dropping out roughly half a minute after you stop touching it, Low Power Mode is on. Apple's own list of what the mode changes includes "Sets Auto-Lock to 30 seconds".

That is the whole explanation, and it is why Never sometimes looks as though it did not save. Turn Low Power Mode off before a session rather than trying to work around it.

Low Power Mode is also the setting most likely to be on without you choosing it, because iOS offers it whenever the battery runs low. A phone that has been projecting for an hour is exactly the phone that gets asked.

Guided Access, for a phone other people can reach

Auto-Lock keeps the screen on. It does nothing about a stray swipe leaving the app, which matters for a display at a party, a stall or a shop window. Guided Access locks the phone to the one app until you end the session.

  • Turn it on at Settings, then Accessibility, then Guided Access, and set a passcode under Passcode Settings.
  • Open the app you want, then start Guided Access with Siri, Control Center or the Accessibility Shortcut.
  • Circle any areas of the screen you want to disable, tap Session Settings to restrict buttons, touch or motion, then tap Start.
  • Guided Access has its own Display Auto-Lock option, which sets how long before the phone locks, so set that too rather than relying on the main setting.
  • End the session by triple-clicking the side button, then entering your Guided Access passcode.

One thing to know before you use it

Apple states plainly that "Crash Detection and Emergency Services aren't available while using Guided Access". You have to exit the session to use either. That is worth knowing before you hand a locked phone to someone for the evening.

Heat and battery on a long session

Driving a projector means the screen on at full brightness, video decoding, and usually a cable carrying power as well as picture. That is a warm phone, and iOS reacts to heat on its own terms.

Apple says iPhone and iPad "are designed for use where the ambient temperature is between 0º and 35º C (32º to 95º F)". Above the normal range, Apple lists what you may notice:

  • "Charging, including wireless charging, slows or stops"
  • "The display dims or goes black"
  • "Cellular signal might weaken as radios enter a low-power state"
  • "The camera flash or other camera features might be temporarily disabled"
  • "In some apps or features, performance is reduced with lower frame rates or increased processing times"

What that means for a two-hour show

The second item is the one that ends a projection. A display that dims or goes black looks exactly like the phone sleeping, so it gets blamed on Auto-Lock and the real cause goes unfixed.

The practical answers are dull and they work. Leave the phone somewhere with air around it rather than face down on a radiator or inside a bag, take the case off if it is a thick one, and keep it out of direct sun and off the projector's own exhaust, which is the hottest air in the room.

Keep it on power, because the screen at full brightness for two hours is more than most phones will carry on battery. Note Apple's own caveat that charging slows or stops when the phone is too warm, so a hot phone on a cable can still lose charge.

Projecting from One Big Projector

One Big Projector is the source, not the light. You design the scene on your iPhone, iPad or Mac, line it up with the real wall or window by dragging corners, and send it out over USB-C or HDMI to an actual projector. Mesh warping wraps content over arches and columns, and the editor handles disappear when you go live, so the projection is clean.

  • Build and preview the scene first, in AR on the real wall if you do not have the projector set up yet.
  • Set Auto-Lock to Never and turn Low Power Mode off before you go live, not during.
  • Use Guided Access if the phone will sit somewhere other people pass.
  • Keep the phone on power and in open air for anything longer than a few minutes.
  • Put Auto-Lock back to its usual time when you are done, since Apple notes that preventing it may increase power consumption.

Questions

How do I stop my iPhone screen turning off while projecting?

Go to the Settings app, tap Display & Brightness, tap Auto-Lock, and choose Never. That keeps the screen on, and the projected picture with it, until you change the setting back.

Why does my iPhone still lock after 30 seconds with Auto-Lock set to Never?

Low Power Mode. Apple's own list of what the mode changes includes "Sets Auto-Lock to 30 seconds", so it overrides your choice while it is on. Turn Low Power Mode off and set Auto-Lock again.

Does keeping the screen awake drain the battery?

Apple does not publish a figure, but it does say that "Delaying or preventing Auto-Lock may increase power consumption". For a long projection, keep the phone on power rather than guessing at how long the battery will last.

How do I stop someone tapping out of the app?

Guided Access, at Settings then Accessibility then Guided Access. It locks the phone to one app until you triple-click the side button and enter your Guided Access passcode. Apple notes that Crash Detection and Emergency Services are not available during a session.

Will my iPhone overheat while projecting for hours?

It can get warm enough for iOS to act. Apple designs iPhone for ambient temperatures between 0 and 35 degrees Celsius, and above the normal range it lists charging slowing or stopping, the display dimming or going black, and reduced performance. A display going black that way looks like the phone sleeping, so give the phone air, take a thick case off, and keep it away from the projector's exhaust.

Does the iPhone itself project the picture?

No. The phone or tablet is the source of the video and sends it over a cable to a real projector, which makes the light. No Apple device projects anything on its own.

Platform facts on this page are quoted from Apple. Auto-Lock steps and the power-consumption caveat: Apple, "Keep the iPhone display on longer" (support.apple.com/guide/iphone/iph7117338a8/ios). The 30-second override: Apple, "Use Low Power Mode to save battery life on your iPhone" (support.apple.com/en-us/101604), whose list includes "Sets Auto-Lock to 30 seconds". Guided Access steps, the Display Auto-Lock option and the Crash Detection warning: Apple, "Lock iPhone to one app with Guided Access" (support.apple.com/guide/iphone/iph7fad0d10/ios). Temperature range and the list of what happens when the device is too warm: Apple, "If your iPhone or iPad gets too hot or too cold" (support.apple.com/en-us/118431). Not stated because no Apple page gives it: any figure for how much faster the battery drains with Auto-Lock off, any time limit for how long a phone can drive a projector before it throttles, and whether the Never option is hidden rather than overridden while Low Power Mode is on. The Never option itself is read from the setting on an iPhone rather than quoted from Apple, whose page says only to choose a length of time. The advice about cases, airflow and projector exhaust is practical guidance, not an Apple instruction.

Try the free projector lumens calculator in your browser

Get One Big Projector on the App Store

More about One Big Projector · Contact us